MiaS13
Driver
Mods Please Sticky
What: Homemade Engine Mounts
Why: Alternative to Hockey Pucks, Nismo Mounts or Stock Mounts
Time: 1 hour
Tools Needed:
Drill with 3/8th Metal Drill Bit
Table Saw or Hand Saw
Tape Measure
Chalk
Materials Needed:
1 - Tube of super glue
2 - 16oz Rubber Mallets
1 - 2ft length of 3/8ths all thread
4 - 3/8ths Nuts
8 - Washers (only 4 pictured)
Step 1
Take your drill and drill a hole straight through the rubber mallet width-wise.
(there's metal in the middle so make sure you have the proper bit)
Step 2
Then Cut the handles off
So they look like this
Step 3
measure the rubber and cut off rubber it until it measures 3 inches
(you can go smaller to lower the motor if you have clearence issues)
like so
Step 4
Cut 2 5&1/4inch lengths of all thread
Step 5
Super Glue your washers around the holes on the rubber
Step 6
Push your 5&1/4inch lengths of all thread through the rubber
Step 7
screw nuts on each side
Final Product
i chose to leave them bare, you can also wrap them in heavy duty tape or what not.
What: Homemade Engine Mounts
Why: Alternative to Hockey Pucks, Nismo Mounts or Stock Mounts
Time: 1 hour
Tools Needed:
Drill with 3/8th Metal Drill Bit
Table Saw or Hand Saw
Tape Measure
Chalk
Materials Needed:
1 - Tube of super glue
2 - 16oz Rubber Mallets
![IMG00025-1.jpg](/proxy.php?image=http%3A%2F%2Fi18.photobucket.com%2Falbums%2Fb105%2FThe1udreamtabout%2FIMG00025-1.jpg&hash=ee086d5679b2169c604338e2c910d9ff)
1 - 2ft length of 3/8ths all thread
4 - 3/8ths Nuts
8 - Washers (only 4 pictured)
![IMG00023.jpg](/proxy.php?image=http%3A%2F%2Fi18.photobucket.com%2Falbums%2Fb105%2FThe1udreamtabout%2FIMG00023.jpg&hash=fd562781e164d2934d63230b515fd683)
![IMG00022-1.jpg](/proxy.php?image=http%3A%2F%2Fi18.photobucket.com%2Falbums%2Fb105%2FThe1udreamtabout%2FIMG00022-1.jpg&hash=563fe29b4e0e4d9d94c7adcb8717fd4c)
Step 1
Take your drill and drill a hole straight through the rubber mallet width-wise.
(there's metal in the middle so make sure you have the proper bit)
![IMG00026-1.jpg](/proxy.php?image=http%3A%2F%2Fi18.photobucket.com%2Falbums%2Fb105%2FThe1udreamtabout%2FIMG00026-1.jpg&hash=3129d5d2edc41291dad8deb42b336dc2)
Step 2
Then Cut the handles off
![IMG00021-1.jpg](/proxy.php?image=http%3A%2F%2Fi18.photobucket.com%2Falbums%2Fb105%2FThe1udreamtabout%2FIMG00021-1.jpg&hash=391570c8b0ae6f80b6f612a05f969f6f)
So they look like this
![IMG00027-1.jpg](/proxy.php?image=http%3A%2F%2Fi18.photobucket.com%2Falbums%2Fb105%2FThe1udreamtabout%2FIMG00027-1.jpg&hash=cde90a3409cb3f230de8a7fd8a238cbb)
Step 3
measure the rubber and cut off rubber it until it measures 3 inches
(you can go smaller to lower the motor if you have clearence issues)
![IMG00028-1.jpg](/proxy.php?image=http%3A%2F%2Fi18.photobucket.com%2Falbums%2Fb105%2FThe1udreamtabout%2FIMG00028-1.jpg&hash=96229dbe386c9a836fb9cd21ca27cf77)
like so
![IMG00024.jpg](/proxy.php?image=http%3A%2F%2Fi18.photobucket.com%2Falbums%2Fb105%2FThe1udreamtabout%2FIMG00024.jpg&hash=5f2b5aa856da5ada58e67ca2943555fb)
Step 4
Cut 2 5&1/4inch lengths of all thread
![IMG00029-1.jpg](/proxy.php?image=http%3A%2F%2Fi18.photobucket.com%2Falbums%2Fb105%2FThe1udreamtabout%2FIMG00029-1.jpg&hash=48a096db2b968f0a902ce2fe4b5ec74c)
Step 5
Super Glue your washers around the holes on the rubber
![IMG00030-1.jpg](/proxy.php?image=http%3A%2F%2Fi18.photobucket.com%2Falbums%2Fb105%2FThe1udreamtabout%2FIMG00030-1.jpg&hash=b3b2260b9e17d7db8fe7648f4e932437)
Step 6
Push your 5&1/4inch lengths of all thread through the rubber
![IMG00031-2.jpg](/proxy.php?image=http%3A%2F%2Fi18.photobucket.com%2Falbums%2Fb105%2FThe1udreamtabout%2FIMG00031-2.jpg&hash=ee678c125e00533106509968d17034a3)
Step 7
screw nuts on each side
Final Product
![IMG00032-1.jpg](/proxy.php?image=http%3A%2F%2Fi18.photobucket.com%2Falbums%2Fb105%2FThe1udreamtabout%2FIMG00032-1.jpg&hash=f8528b9b7abd87963809f53d2d4afd62)
i chose to leave them bare, you can also wrap them in heavy duty tape or what not.